The LG.com website utilizes responsive design to provide convenient experience that conforms to your devices screen size. In order to get the best possible experience our LG.COM website please follow below instructions. Replace it only with an exact factory replacement part. Electric shock or fire may occur due to electrical damage of power cables. Do not place heavy objects on the refrigerator. Falling objects when opening or closing doors may cause injury. Do not hang or swing from the refrigerator doors. Do not allow children to play with the refrigerator.
This refrigerator repair guide gives step-by-step guidelines for replacing the defrost sensor in a side-by-side refrigerator. The defrost sensor-also called a defrost bi-metal thermostat-shuts off the defrost heating unit if the heater gets hot plenty of to harm the evaporator. If the defrost sensor breaks down, the heating element doesn't turn on, and ice develops up on the evaporator ensuing in cozy temperatures in the refrigerator. If your defrost sensor is faulty, replace it with the manufacturer-approved replacement part.
Make use of this fix procedure on Kenmore, Whirlpool, KitchenAid, Maytag, Amana, GE, Frigidaire, Electrolux, Bosch and Samsung side-by-side refrigerators.
Fix problems:
Period required:
Less than 45 minutes.
Components Required
- Defrost sensor
- Cable jewelry
- Silicon sealant
- Wire nuts
For guides, repair guides, and specific part suggestions, enter your model amount.
Tools Required
- 1/4' nut motorist
- Screwdriver
- Work mitts
- Wire stripper
Before you begin
Wear work hand protection to defend your fingers. Safely store any foods that could weaken while the refrigerator will be close off.
Warning:Undertaking maintenance to home appliances can be hazardous. Make use of the appropriate tools and safety equipment mentioned in the guidebook and adhere to all guidelines. Do not really move forward until you are usually assured that you recognize all of the steps and are capable of finishing the restoration. Some repairs should just be carried out by a experienced specialist.
Unplug the refrigerator or close off the routine breaker for the refrigerator.
Remove the racks and baskets from the refrigerator compartment. Remove the screws from the shelf facilitates on the correct interior walls of the fridge and draw the helps away.
Suggestion:If required, relate to your owner's regular for assistance in eliminating containers and racks from the freezer.
Get rid of the racks and containers.
Get rid of the right-side space supports.
Get rid of the increasing screws that protected the inside of back board of the refrigerator. Pull the bottom part of the -panel outward slightly to launch it.
Remove the back again panel anchoring screws.
Eliminate the back again -panel.
Stage 4:Unclamp the defrost sensor from the evaporator
Note the setting of the defrost sensor. Discharge the metallic clip that holds the defrost sensor to the refrigerant series located above the evaporator.
Tip:Get a electronic photograph of the defrost sensor to assist you position the replacement correctly.
Launch the clip that secures the defrost sensor to the refrigerant collection.
Reduce the dark brown and pink wires near the defrost sensor and pull the defrost sensor out of the freezer.
Make use of a cable stripper to eliminate the insulation from the finishes of the pink wire and brownish cable on the fresh sensor. Strip the finishes of the red cable and brown wire in the funnel above the evaporator. Make use of wire nut products to connect the matching cables.
To maintain the connection dry, squeeze silicon sealant into the open up ends of the cable nut products.
Phase 7:Clip the defrost sensor onto the refrigerant range
Clip the brand-new defrost sensor onto the refrigerant collection above the evaporator. Place it in the same manner as the primary defrost sensor.
Without troubling the sealant on the wire nuts, push the wires above the evaporator. Use a cable connection tie up to fasten the wires to additional cables in the safety belt to maintain them out of the method.
Reinstall the back again panel and replace the mounting screws. Over tightening up the screws can break the fridge liner or the mounting track. Rotate the anchoring screws until they cease and then snug them up with a last perspective. Reinstall the baskets and racks.
Put in the refrigerator or change on the home routine breaker to bring back power.